TSS Limiter Pro v.3.5 (included logger)

Limiter for ship models with online telemetry and logger

Price: €160

add to cart

Description

The energy limiter for radio-controlled models (hereinafter the limiter) is intended for calculation and limitation of the energy consumed by the model.

The "PRO" version differs from the "LITE" version in the presence of a logger.

The device is equipped with the Bluetooth Low Energy (BLE) interface for communication with mobile devices or computers which allows to perform its settings and receive the current readings without need of having direct access to and its removing from the model.

The device can be used both for running the competitions to limit the energy consumed by the model from the accumulator and for training intentions to set the model and take the actual readings on current, voltage, energy and consumable battery capacity.

The device fully meets the Naviga requirements which allows using it in all kinds of registered or non-registered competitions according to Naviga rules. In event of rule changes, the new array of device settings will be available in new firmware upgrades of the device. The firmware upgrade is performed through the user`s phone, you need not send the device anywhere.

Technical specification

Parameter

Value

Note

Measured voltage

0 – 52V (12S)

DC

Voltage measurement accuracy

±0.05% + ±5mV

 

Measured current (up to 20 sec)

1 – 150A

 

Measured current (DC)

1 – 100A

 

Current measurement accuracy

±0.25% + ±40mA

 

Measured energy

0 – 300,000Wh

 

Energy measurement accuracy

±0.5%

 

Sampling frequency

10kHz

 

Series resistance

0.25mOhm

 

Current consumption

6mA

 

BEC voltage

4 – 8.4V

 

Type of communication interface

BLE

Bluetooth Low Energy 5.0

Communication Interface range

100m

In direct visibility

Receiver signal

0.7 – 2.3ms

Standard PPM 3.3-10V

Working temperature range

0 – 50⁰C

 

IP rating

IP67

 

Dimensions of the device

22.5 х 19.5 х 10.5mm

No wires included

Weight

22g

Including all wires and plugs

Wire to receiver length

240mm

 

Wire to ESC length

40mm

 

Type of signal wires

26AWG (JR)

 

Length of the power wire

100mm

 

Short description

In total, the device has 14 sets of settings, 8 (6 - 14) of which are user-defined and are subject to change.

The device has 6 sets of preset settings. These settings cannot be changed and 1 – 5 sets fully comply with the Naviga rules.

Telemetry

The device is equipped with integrated telemetry module.

Telemetry display the following parameters:

  • Current;
  • Average current for 10 seconds;
  • Voltage;
  • Measured energy;
  • Measured capacity;
  • Temperature (own);
  • Power consumption for the race (economizer);
  • Average current for the race;
  • Average voltage for the race;
  • Measured race time.

Configuration

The basic settings of the limiter can be changed using a button that is connected via a wire that goes to the receiver.

Functions of setting by button is given in the table:

Settings set number

Purpose

Energy limitation

0

Training mode, telemetry only

1

Mini Eco, Mono, Hydro

21Wh

2

Eco Expert, Mono I, Hydro I

60Wh

3

Mono II, Hydro II

120Wh

4

FSR-E

180Wh

5

FSR-E mini

42Wh

User manual

TSS Limiter User manual.pdf

Logger

The device is equipped with integrated logger module.

The log recording frequency is adjustable in the range from 1 to 100Hz. The recording time at a frequency of 10Hz is 1 hour 46 minutes, at a frequency of 100Hz 10 minutes 37 seconds.

The speed sensor supports motors from 2 to 20 poles.

Logger write to internal flash memory following parameters:

  • Current;
  • Voltage;
  • Energy;
  • Capacity;
  • Temperature (own);
  • Energy consumption (economizer);
  • RPM;
  • Speed (if TSS GLONASS GPS Module used);
  • GLONASS/GPS satelites (if TSS GLONASS GPS Module used);
  • Measured race time.